UNITED STATES STOVE KING KP130 OWNER'S OPERATION AND INSTRUCTION MANUAL Pdf Download (2024)

4

LABELING VENDOR NOTES:

MATERIAL: 0.012 THK. ALUMINUM / 3M 9672 ADEHESIVE BACKED.

FINISH: BLACK BACKGROUND, ALUMINUM TO SHOW THRU

(ALL TEXT AND ILLUSTRATIONS) UNLESS NOTED OTHERWISE.

TEXT: ALL TEXT TO BE 0.07 HIGH UNLESS OTHERWISE SPECIFIED

B

0.25 TEXT HEIGHT

0.125 TEXT HEIGHT

0.10 TEXT HEIGHT

A

SERIAL & DATE BOX

DETAIL

1.50

[38.1mm]

0.25

[6.4mm]

4

3

ALL PLATES ARE TO BE STAMPED BY THE HEATER MFG. WITH A

FACTORY IDENTIFIER NUMBER ISSUED BY USSC. (i.e. 00000-XX)

WHEN LABEL IS APPLIED TO THE HEATER, IT IS TO BE FIRMLY

PRESSED OVER THE ENTIRE SURFACE TO ENSURE IT PROPERLY

1 INCH SQ. BORDER, LOGS

AND FLAMES ARE TO BE RED

0.25 TEXT HEIGHT

ATTENTION:

HOT WHILE IN OPERATION-DO NOT TOUCH

KEEP CHILDREN AND CLOTHING AWAY -

CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND

INSTRUCTIONS. KEEP FURNISHINGS AND OTHER COMBUSTIBLE

MATERIALS A CONSIDERABLE DISTANCE AWAY FROM THE APPLIANCE.

ATTENTION:

OPERATE THIS UNIT ONLY WITH THE FUEL HOPPER LID

CLOSED. FAILURE TO DO SO MAY RESULT IN EMISSION OF

PRODUCTS OF COMBUSTION FROM THE HOPPER UNDER CERTAIN CONDITIONS.

MAINTAIN HOPPER SEAL IN GOOD CONDITION. DO NOT OVERFILL THE HOPPER.

CAUTION: Moving parts may cause injury. Do not operate with the side panels or repair panel removed. Do not place hands or fingers in the moving auger area at

the bottom of the hopper. Do not obstruct the combustion air inlet opening at the rear of the appliance.

DANGER: Risk of electrical shock. Disconnect power before servicing unit. Route power supply cord away from the appliance.

Keep viewing and ash removal doors tightly closed during operation. Replace glass with 5mm ceramic glass ONLY.

IMPORTANT: When the hopper lid is open, the auger will stop. Close the hopper lid to allow system to operate. Provide a source of fresh air to the room where the appliance

is installed. Do not obstruct the space beneath the appliance. Inspect and clean exhaust vent system frequently in accordance with manufacturer's instructions.

Install and use only in accordance with the manufacturer's installation and operating instructions. Contact local building or fire officials about restrictions and

installation inspection in your area. Do not install in a sleeping room.

Do not connect this unit to a chimney flue serving another appliance. Refer to local building codes and the installation and operating instructions for precautions

required for passing an exhaust venting system through a combustible wall or ceiling.

Components required for residential or mobile home installation: Model PL Vent Chimney and Components - 3"/75mm or 4" 100mm diameter.

This wood heater needs periodic inspection and repair for proper operation. Consult the owner's manual for further information. It is against federal regulations to

operate this wood heater in a manner inconsistent with the operating instructions in the owner's manual.

START-UP / Automatic Ignition - Press the ON/OFF button. Green power light begins to blink. When the light becomes solid, set the desired heat level.

SHUT DOWN: Press the "OFF" button. Unit will shutdown automatically after fuel burns out and unit cools down.

MODEL / MODÈLE : KP130

Serial No. /

o

N

de série

Manufacture Date. /

Date de Fabrication

U.S. Stove Company • 227 Industrial Park Road • South Pittsburg, TN 37380 • Phone: (800) 750-2723 • Web: www.usstove.com

© 2010 United States Stove Company

THE DATA CONTAINED HEREIN IS PROPRIETARY TO U. S.

STOVE COMPANY. THIS DATA SHALL NOT BE DUPLICATED,

TRANSFERRED, MADE AVAILABLE, OR USED BY ANY THIRD

PARTY FOR ANY PURPOSE EXCEPT SPECIFICALLY

AUTHORIZED IN WRITING BY U. S. STOVE COMPANY.

3

HEATER MANUFACTURER INSTRUCTIONS:

ADHERES TO THE MATING SURFACE OF THE HEATER.

0.125 TEXT HEIGHT

ATTENTION:

TOUT CONTACT PEUT ENTRAÎNER DES BRÛLURES. CONSULTER LA PLAQUE

SIGNALÉTIQUE ET LES INSTRUCTIONS. MAINTENIR LE MOBILIER ET LES AUTRES

MATIÈRES COMBUSTIBLES À BONNE DISTANCE DE L'APPAREIL.

ATTENTION:

PAS LE FAIRE PEUT ENTRÎNER DES ÉMISSIONS DE PRODUITS DE LA TRÉMIE DANS

CERTAINES CONDITIONS. D'ASSURER L'ÉTANCHÉITÉ TRÉMIE EN BON ETAT. NE PAS

SURCHARGER LA TRÉMIE.

ATTENTION: Les pièces en mouvement peuvent provoquer des blessures. Ne pas faire fonctionner cette unité avec les panneaux latéraux ou le panneau arrière

retirés. Ne pas placer les mains ou les doigts à l'intérieur de la zone de la vis sans fin en bas de la trémie. N'obstruez pas l'admission d'air de combustion.

DANGER: Risque de choc électrique. Déconnecter l'alimentation avant de réaliser l'entretien de l'unité. Faire passer le cordon d'alimentation à distance de l'unité.

Maintenir les portes d'inspection et de retrait des cendres bien fermées pendent le fonctionnement. Remplacer le verre uniquement par du verre céramique (5mm).

IMPORTANT: Quand le couvercle de la trémie est ouvert, la vis sans fin d'alimentation s'arrêtera. Fermer le couvercle pour permettre au système de fonctionner.

Fournir une source d'air frais dans le chambre. Ne pas obsturer l'espace sous l'app. de chauffa*ge. Inspecter et nettoer fréquemment le système de ventilation

d'évacuation conformément aux instructions du fabricant.

Installer et utiliser conformément aux instructions du fabricant uniquement. Contacter les fonctionnaires locaux de construction ou fonctionnaires des services

d'incendie concernant les limitations et l'inspection de l'installation dans votre maison. Ne pas installer dans une chambre à coucher.

Ne pas connecter cette unité à un carneau de chiminée utilisé pour un autre appareil. Consulter le code local de construction et les instructions du fabricant pour les

précautions requises pour passer à travers un mur ou un plafond combustible.

Composants nécessaires pour une installation dans une résidence ou une maison mobile: Ventilation modèle PL chiminée et composants - Diamètre de 3"/75mm ou

4"/100mm.

Ce poêle à bois doit inspection et la réparation périodique. Pour un fonctionnement correct, consultez le manuel du propriétaire pour plus d'informations. Ce est

contre les règlements fédéraux pour faire fonctionner ce poêle à bois d'une manière incompatible avec les instructions d'utilisation dans le manuel du propriétaire.

MISE en MARCHE / Allumage Automatique - Appuyer sur le buoton ON/OFF. Le voyant vert se met à clignoter. Lorsque le voyant s'arrête de clignoter et reste

allumé, régler le thermostat au niveau souhaité.

ARRÊT: Placer le réglage de chaleur sur "OFF". L'unité s'éteindra automatiquement une fois que le combustible sera consumé et que l'unité ait refroidi.

ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2020 particulate

emission standards. Tested to ASTM E2779 /

EPA Method 28R - 1.27 g/hr.

A -

2" / 50mm

B - 13" / 330mm

C -

8" / 203mm

D -

8" / 203mm

E -

36" / 914mm

F -

60" / 1.52M

Report No. / Rapport No.

Report No. / Rapport No.

215-S-05c-2

18-439

DO NOT REMOVE OR COVER THIS LABEL / NE PAS RETIRER OU COUVRIR CETTE ÉTIQUETTE

12.00

[304.8mm]

DESCRIPTION

HOLES

TOLERANCES

± .005"

ALL RIGHTS RESERVED

EXCEPT

DECIMAL

FINISH

.XX = 0.03 XXX = 0.010

AS

ANGULAR

REFERENCE

NOTED

± 2°

2

REV

A

B

0.125 TEXT HEIGHT

0.25 TEXT HEIGHT

CHAUD PENDANT LE FONCTIONNEMENT-NE PAS TOUCHER

MAINTENIR LES ENFANTS ET LES VÊTEMENTS ÉLOIGNÉS.

FAIRE FONCTIONNER CETTE UNITÉ UNIQUEMENT AVEC LE

COUVERCLE DE TRÉMIE DU COMBUSTIBLE FERMÉ. NES

Clearances to Combustibles: Residential and Mobile Home

Dégagements Combustibles: Dans Une Résidence ou Une Maison Mobile

Alcove

Backwall/Sidewall

Corner/Coin

Mur Arriére/Paroi Latérale

A

D

E

A

B

F

C

C

D

SCALE

SIZE

REV

SEE NOTE

1:1

B

B

DWN BY

SEH

TITLE

DATE

CERTIFICATION PLATE

3/4/13

KP130

2

REVISION HISTORY

DESCRIPTION

DATE

BY

INITIAL RELEASE

2/27/18

SEH

3/29/19

SEH

B

5.50

[139.7mm]

1/2"(12.5mm) or 1"(25mm) Thick/Épais

Non-Combustible Floor Protection /

Un Protecteur de sol Non-Combustible

6 in (152mm)

Canada - 8" (203mm)

Thickness /

k-value

1/2" / 0.042

A

1" / 0.084

6 in (152mm)

Canada - 18" (450mm)

853144B

ESTABLISHED 1869

NUMBER

SHEET

853144

1

1

OF

1

UNITED STATES STOVE KING KP130 OWNER'S OPERATION AND INSTRUCTION MANUAL Pdf Download (2024)

FAQs

Why is my king pellet stove not starting? ›

Troubleshooting a Pellet Stove That's Not Igniting

Inspect the Airflow: Check the air inlet pipe, the outside air kit, and any areas inside the stove downwind from the burn pot for blockages. This includes behind the baffles, inside the air chambers leading to the exhaust blower, and the exhaust venting.

What is the er2 code on a king pellet stove? ›

Error code #2 according to your manual is: hopper empty, auger output failure or jam, flame of fuel quality caused fire to burn too slowly or go out, electrical open in low temperature switch or wiring.

Is the stove KP130? ›

The US Stove KP130 is a fully automated pellet stove with auto ignition and easy to use electronic controls.

How do I fix error 2 on my pellet stove? ›

Error Code 2: Auger Jam

Motor failure. Solutions: Shut down the stove and clear any blockages in the auger. Inspect and replace a malfunctioning auger motor.

What causes pellet stove to not feed pellets? ›

The hopper may be empty. Fill the hopper and allow a few minutes for the unit to auger the pellets onto the burn pot. Venting may be blocked. The Pressure Switch senses a lack of air flow and will shut the motors off.

Why is my pellet stove fan not kicking on? ›

Probable cause: The pellet vent is clogged. Either the motors are dirty or need replacing. If a blower requires replacing, ensure to identify which blower (convection – pushes heat into the home whereas combustion - pushes exhaust outside; or auger motor - feeds pellets into the burn pot).

What does ER2 mean on a smoker? ›

Receiving an ER-2 means failure to light. You will see this error code if your recteq does not reach 180° within 30 minutes. Causes: Auger Jam/Pellet Bridge - The fuel is unable to reach the fire. Airflow - Blower fan is not supplying airflow to the fire.

Why is my stove chirping? ›

The most common reasons for an oven to make a beeping noise include preheating alerts, timer alerts, and temperature gauge alerts. However, if your oven is overheating or displaying an error code, the beeping may be a signal that service is required.

What stove do chefs use at home? ›

Viking 5 Series 30-Inch Open Burner Gas Range

If you ask a professional chef what range brand they fantasize about, nearly all will answer Viking.

What is a lazy flame in a pellet stove? ›

MOST pellet stove are Negative air. ( Inside of the Firebox is negative pressure ) If you don't have the ash pan or door sealed less air will flow through the burn pot and you will have a tall lazy flame. You will see no visual change in the fire when you change the air control.

What is error 3 on a King pellet stove? ›

I get an error message 3. The manual says this error indicates “The stove was unable to reach the Room Fan On temperature within the startup time.” The cause is “Flame or Fuel quality caused the fire to burn too slowly or go out. Auger output failure or jam Hopper empty on startup.”

What does a thermocouple do on a pellet stove? ›

The thermocouple signals the control box to call for more fuel when the fire reaches a specific temperature range. When the thermocouple senses the appropriate heat level in the firepot, it signals the control box to pause the pellet feed again.

Why is my pellet stove not getting hot enough? ›

If you notice that your stove isn't burning pellets as well as it should or producing as much heat as it was, air flow may be to blame. Check the stove's door to make sure it is sealing securely and that no air is escaping through the door. A blocked air inlet cap also could be to blame.

What would cause a pellet stove to not turn on? ›

In conclusion, ignition failures in pellet stoves and pellet stove inserts can often be traced back to issues with the exhaust fan, auger, igniter, airflow, and burn pot cleanliness.

Why pellets won't ignite? ›

The first thing to check when your grill isn't igniting is the pellets in the firepot and in the hopper. Pellets should have a nice sheen and have a "snap" to them when breaking (similar to a pencil). If the pellets crumble or are dull looking (not shiny), empty your hopper and try a new bag of pellets.

Do pellet stoves have a reset button? ›

Many pellet stoves do not have a pellet stove reset button. Instead, you can reset them by letting the pellets run out. This way, you don't have to try to move pellets out of the stove when you are not sure if it is hot. Once the stove runs out of pellets, it will no longer be able to heat.

Top Articles
Latest Posts
Article information

Author: Golda Nolan II

Last Updated:

Views: 5766

Rating: 4.8 / 5 (78 voted)

Reviews: 85% of readers found this page helpful

Author information

Name: Golda Nolan II

Birthday: 1998-05-14

Address: Suite 369 9754 Roberts Pines, West Benitaburgh, NM 69180-7958

Phone: +522993866487

Job: Sales Executive

Hobby: Worldbuilding, Shopping, Quilting, Cooking, Homebrewing, Leather crafting, Pet

Introduction: My name is Golda Nolan II, I am a thoughtful, clever, cute, jolly, brave, powerful, splendid person who loves writing and wants to share my knowledge and understanding with you.